YOTENKO
CB Coax Cable, 75FT RG58 Coaxial Cable, UHF PL259 Male Coax 50
Disclosure: We may earn a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Learn more
Highlights
- 【Cable Type & Details】- Cable & Connector: RG 58 coaxial cable with pl259 connectors on both ends ▏Inner Conductor Material: bare copper▏Impedance: 50 ohm ▏Dual shield
- ⭐【Heat shrink tube lengthened to 6 cm】- Compared with other UHF cable,our improved heat shrink tube has been lengthened to 6cm,both ends are heat shrinkable and firmly connected,which make the UHF male connectors of the patch cable firmer and effectively prevent connectors from falling off the cable due to bending / pulling.
- 【High Cost-Performance Low Loss Cable】- 75ft ham radio coax cable is made of bare copper inner conductor,copper-clad steel braid and Aluminum foil outer conductor,PE Insulation,PVC Sheath.The dual shield could maximum protect the signal.This well made patch cord has little effect when inserting your devices,it is a good choice.
- 【Application】- This 50 Ohm pl 259 coaxial cable is widely used in HF/VHF equipment in the 0-300MHz frequency band, such as CB Radio ,Ham Radio,Amateur Radio,Power/SWR Meter,Transceiver,HF Radio,VHF Radio,Antenna,Surge Protector,Walkie Talkies,Marine Boat Antenna Radio,Antenna Analyzer,Antenna Tuner,Dummy Load,Radio Scanner,Linear Amp,etc.
- 【Package Included】- 1x 75 Feet Male PL259 to Male PL259 RG58 Coax Cable
Why You'll Love It
- 75-foot length provides generous reach between your radio transceiver and outdoor antenna setup
- Dual-shielded design with aluminum foil and copper-clad steel braid helps protect signal integrity
- Bare copper inner conductor ensures reliable 50-ohm signal transmission across HF and VHF gear
- Extended 6-centimeter heat shrink tubing prevents connectors from pulling loose during bending
- Pre-installed male PL-259 connectors offer direct compatibility with standard amateur radio equipment
Pros
- +Generous 75-foot run
- +Dual-shielded cable design
- +Reinforced 6cm heat shrink
- +Standard 50-ohm impedance
- +Bare copper inner core
Cons
- -Fixed male PL-259 connectors on both ends
- -Limited to 0-300MHz frequency equipment
Detailed Review
The YOTENKO 75ft RG58 Coaxial Cable provides a ready-to-use connection between antennas and radio transceivers. Designed specifically for standard 50-ohm systems, this 75-foot assembly eliminates the hassle of cutting wire and soldering your own ends, making it a dependable choice for setting up CB rigs, ham radio stations, or marine antennas.
Signal quality depends heavily on internal construction, and this cable uses a bare copper center conductor paired with dual shielding. Between the aluminum foil layer and copper-clad steel braiding, the cable protects your transmission from interference while maintaining minimal insertion loss. The core is protected by PE insulation and an outer PVC sheath designed for everyday handling.
A notable feature is the reinforced connection point at each UHF male PL-259 plug. The manufacturer uses extended 6cm heat shrink tubing on both ends. This extra reinforcement provides vital strain relief, keeping the connectors firmly attached even when the line is pulled, bent, or routed through tight spaces around equipment racks.
Because this is a dedicated RG58 line with male UHF terminations, it is built specifically for HF and VHF gear operating within the 0 to 300MHz range. It is not intended for UHF setups operating above 300MHz or hardware requiring different connector types like BNC or N-type without adapters.
Verdict: This YOTENKO 75-foot cable is an excellent, pre-assembled solution for operators setting up CB, amateur, or marine radio gear in the 0-300MHz range. Its dual shielding and reinforced heat shrink make it a reliable link for your station.
Specifications
- Length: 75 feet
- Cable Type: RG58 coaxial
- Connectors: UHF PL259 Male to PL259 Male
- Impedance: 50 Ohm
- Inner Conductor: Bare copper
- Outer Shielding: Aluminum foil and copper-clad steel braid
- Insulation & Jacket: PE insulation with PVC sheath
- Frequency Range: 0-300MHz (HF/VHF)
- Strain Relief: 6cm heat shrink tubing on both ends
Who Should Buy It
A great fit if you:
- Need a long 75-foot patch line to connect an antenna to a CB, ham, or marine radio transceiver.
- Want pre-installed, reinforced PL-259 male connectors that resist strain from pulling and bending.
- Operate HF or VHF equipment functioning in the 0 to 300MHz spectrum.
- Use antenna analyzers, SWR meters, tuners, or linear amps with standard SO-239 female jacks.
Consider something else if you:
- Operate equipment above the 300MHz frequency threshold.
- Require BNC, SMA, or N-type connections without using separate adapters.
FAQ
What connectors come installed on this cable?
The cable comes pre-assembled with male PL-259 (UHF male) connectors on both ends.
What frequency range is this coax designed for?
It is designed for HF and VHF applications operating across the 0 to 300MHz frequency band.
What is the cable impedance and shielding construction?
It is a 50-ohm cable built with dual shielding, featuring an aluminum foil layer and a copper-clad steel braid over a bare copper inner conductor.
Product Details
| Brand | YOTENKO |
| ASIN | B0BJYXFVWT |
